ACOM ATU 04AT Remote Antenna Tuner
- Overview
- Specifications
- Powered and controlled directly from the ACOM solid state HF+6m amplifiers through the amplifier RF output cable only - there is no need for power or control cables between the shack and the tuner.
- Provides automatic or manual antenna change and automatic antenna impedance matching to the ACOM solid state HF + 6m amplifiers, controlled entirely from the amplifier front panel and your transceiver CAT.
- Guards the transceiver and amplifier against excessive impedance mismatch during the tuning process.
- Operates with two types of tunings: full tuning (basic matching cycle) and fast tuning (retrieving user tuning patterns from nonvolatile memory.
- Full tuning is 100% automated however a cycle is initiated only by the operator. User tunings track the antenna and frequency changes automatically during amplifier and transceiver operation.
- Four typical antenna types: Regular, Sharp, Wide, and Fixed-frequency are available so the operator can adapt the frequencysegment width to the specific antenna bandwidth; BYPASS mode is also available.
- Antennas appear with a number, type, and user-editable name on the ACOM solid state amplifiers screen.
- Tunings availability presented by a graphic scale on the ACOM solid state amplifiers screen.
- A plenty of antenna- and tuner- related information is available on the ACOM solid state amplifier screen: menus ATU SERVICE, ATU MEASURE, ATU TUNINGS LOOKUP/ERASE, Resource-estimate function etc.
- Tuning “age” warning can be set to warn you when you attempt to use an outdated tuning.
- The user can archive all tunings from nonvolatile memory in a computer file as well as upload earlier archived files in the ACOM 04AT nonvolatile memory through the ACOM solid state amplifier’s RS232 port.
- Protections: PS voltage, Reverse PS polarity, Excessive RF voltage, RF current or reflected power at the antenna outputs,
- Excessive tuning power, Excessive Input power, Hot switching of relays, Overheating etc.
- Protected against building of static electricity in the antennas via bleeding resistors and against close lightning strikes via gasfilled discharger; unused antennas are directly grounded during operation as well as all antennas are when the ACOM 04AT is powered off.
Download the manual click here
- Frequency coverage: 1.8 to 30MHz and 50 to 54MHz, continuously (30 to 50MHz on request).
- Antenna impedance matching capability: all impedances with 50 Ohm-SWR between 1 and 3; (for some higher-SWR impedances matching is also possible
- see power limitations below).
- Maximum RF Input power admissible, average or continuous (no mode limitations; in brackets - PEP):
-At antenna SWR below 2:1500W (1500W PEP);
-At antenna SWR between 2 and 3:1200W (1500W PEP);
-At antenna SWR between 3 and 5 (provided matching is possible): 700W (1000W PEP);
-At antenna SWR between 5 and 10 (provided matching is possible): 350W (500W PEP);
- Rem: Operation at SWR above 10 is not permitted even though matching could be possible in some cases.
- RF Input characteristics:
-Nominal impedance: 50-Ohm unbalanced;
-Connector type: UHF/PTFE (S0239A);
-Input SWR during full tuning (basic matching cycle): below 1.8;
-Input SWR soon after full tuning: less than 1.5 (below 1.3 typ.).
- Antenna output characteristics:
-Nominal impedance: 50-Ohm unbalanced;
-Connector type: UHF/PTFE (S0239A);
-Number of outputs - 4;
-Antenna SWR: between 1 and 3 for 100% matching, full power; for higher-
- SWR impedances (provided matching is possible) see power limitations above).
- Full tuning duration (basic matching cycle):
-Below 10MHz: less than 5s (2-3s typ.)
-Above 10MHz: less than 3s (1-2s typ.).
- RF Input power required during full tuning: 25W +3/-3 dB (12.5 to 50 W), non-modulated.
- Fast tuning duration: less than 50ms (from nonvolatile memory).
- Power supply and control: available from the ACOM solid state HF+6m amplifiers through RF-output coaxial cable; +26VDC, up to 25 W consumption; control data using a FSK modem at 60 kHz.
- Coaxial cable maximum length (same for RF power, DC power supply, and control):
-61 m (200 feet) for cable type RG-58;
-305 m (1000 feet) for cable type RG-213.
ATTENTION! In order to keep possible RF loss at a minimum, use only the minimum length needed to install the ACOM 04AT tuner and switch as close to the antennas as practical.
- Size and mass (operating) W 510 mm (20.1”) x D 400 m (15.8”) x H 300 m (11.8”); 7.0 kg (15.43 lbs).
- Operating environments:
-Weather protection: IP 53 (NEMA Type 3);
-Temperature range: -40 to +65 degrees C (-40...+150F);
-Humidity: up to 98% @ +40 degrees C (104F);
-Height ASL without parameters deterioration: up to 3050 m (10 000 feet).
- Acom Aerial Tuning Units£999.95(Inc VAT at 20%)