The IC-7200 HF/50MHz transceiver maintains all the traditions of high quality engineering that you expect from Icom. Rugged in design and easy to operate, the IC-7200 utilises the latest digital functions including digital IF filter, twin PBT and manual notch filter which are normally associated with more expensive models.
Simple & Tough with IF DSP
The latest IF DSP technology is employed in the IC-7200. While the IC-7200 is an entry-class transceiver, advanced digital features are comparable to higher class transceivers.
AGC loop management
Distortion and blocking from strong nearby signals are prevented by placing DSP functions inside the AGC loop. The AGC time constants are selectable from fast, slow and off for each operating mode.
Digital IF filter
Optional filters will be never required for the IC-7200. The built-in digital filter allows you to flexibly select the filter width and shape from soft and sharp* and provides cuttingedge filter characteristics.
Digital Twin PBT
Only Icom brings you Twin Passband tuning! Tailor your IF passband with the Twin PBT by electronically shifting the upper and lower edges of the IF filter. Depending on the use of the concentric knobs, you can either narrow the IF passband, or shift the entire passband to eliminate interfering signals.
Manual notch filter
The manual notch filter delivers more than 70dB of attenuation. Strong interfering tones will be eliminated without adversely affecting the AGC loop performance. On the bottom right of the front panel, a dedicated control knob adjusts the notch filter frequency.
Digital noise reduction
Digital noise reduction reduces background noise and improves the signal-to-noise ratio. The noise reduction level is adjustable in 16 steps. It improves the readability of voice and data signals.
Digital noise blanker
The noise blanker reduces pulse-type noise such as engine ignition and sparking. The NB level and width (blanking duration) are adjustable in 100 steps.
High stability transmitter
The DDS (Direct digital synthesizer) creates a clear, clean transmit signal and improves the C/N ratio. With a dual-fan cooling system, the IC-7200 provides stable high quality output even during high duty cycle operation.
USB port for PC control
The IC-7200 can be controlled by a PC through a USB port using the CI-V data format. In addition, modulator and received audio can also be transferred over the USB cable. By using appropriate external software, you can record incoming call and/or transmit preprogrammed messages from your PC.
RF speech compressor
The digital RF speech compressor increases your average talk power in SSB mode. Even when the compression level is increased, the DSP controlled RF speech compressor provides low distortion audio.
CW mode operation
Full break-in, selectable CW carrier point (USB or LSB) and adjustable CW pitch are also standard.
Tough construction against water intrusion
Waterproof protection technologies that are used in Icom’ s marine radios are applied to the buttons and knobs on the front panel to provide a measure of protection against water intrusion.
Rugged design for outdoor use
The rugged design of the IC-7200 means your enjoyment of this rig is not limited to your shack only.
- ±0.5ppm frequency stability
- LCD backlight (Hi/Lo/Off)
- CI-V interface
- 201 memory channels
- Built-in 20dB attenuator
- Dial lock
- Auto TS function
- 1Hz step tuning
- Band stacking register
- Built-in voice synthesizer
- Quick split
- Front facing speaker
- Quick set mode
The “rear bumper” protects various connectors on the rear panel and lets you stand the radio on its rear end when the antenna is disconnected, such as while moving or packing the radio.
|Frequency coverage*1 |
(Differs according to version)
|Rx : |
1.800– 1.999999MHz 3.500– 3.999999MHz
5.255– 5.405MHz*3 7.000– 7.300MHz
|Mode||USB, LSB, CW, RTTY (FSK), AM|
|Frequency stability||Less than ±0.5ppm|
|Maximum current drain||22.0A|
|Power supply requirement||13.8V DC ±15 % (negative ground)|
|Antenna connector||SO-239 (50Ω)|
|Number of memory |
|201ch (199 regular, 2 scan edges)|
are not included)
|241×84×281 mm |
|Weight (approx.)||5.5 kg; 12.1 lb|
|Output power|| |
SSB, CW, RTTY:
|Spurious emissions||Less than –50dB (HF) |
Less than –63dB (50MHz)
|Carrier suppression||More than 50dB|
|Unwanted sideband||More than 50dB|
|Microphone connector||8-pin connector (600Ω)|
(10dB S/N, Preamp ON, Filter shape sharp)
|SSB, CW: |
Less than 0.16μV (1.8–29.995MHz):
Less than 0.13μV (50MHz band)
Less than 13μV (0.5–1.8MHz)
Less than 2μV (1.8–29.995MHz)
Less than 1μV (50MHz band)
|Selectivity||SSB(BW: 2.4kHz, sharp): |
More than 2.4kHz/–6dB
Less than 3.6kHz/–60dB
CW(BW: 500Hz, sharp) :
More than 500Hz/–6dB
Less than 900Hz/–60dB
RTTY (BW: 350Hz):
More than 360Hz/–6dB
Less than 650Hz/–60dB
AM (BW: 6kHz):
More than 6.0kHz/–6dB
Less than 15.0kHz/–60dB
|Spurious and image |
|More than 70dB |
(Except 1⁄2 IF through on 50MHz band)
|AF power |
(at 10% distortion with an 8Ω load)
|More than 2.0W|
|External speaker |
|2-conductor 3.5 (d) mm (1⁄8″) /8Ω|
All stated specifications are subject to change without notice or obligation.