We use
cookies and similar technologies
to help give you the best experience on our site and to show you relevant advertising. If you continue to use this site, we’ll assume that you’re happy to receive all cookies
SPE EXPERT 2K-FA - 2 KW Solid State Fully Automatic Linear Amplifier
SKU Part Number:
2K-FA
The smallest in its class. Built-in Power supply and Automatic Antenna Tuner.
Dimension: L 38, H 18.3, P 43 cm (14.96” W, 7.20” H,16.93” D)...
Read More
Read More
Special Price
£5,499.00
£4,582.50
Regular Price
£5,749.99
£4,791.66
Pre Order

Seen this product cheaper elsewhere?
Call 0345 2300 599The smallest in its class. Built-in Power supply and Automatic Antenna Tuner.
Dimension: L 38, H 18.3, P 43 cm (14.96” W, 7.20” H,16.93” D) (connettors included).
Weight: approx: 25 Kg.(55lbs).
The most technologically advanced in the world
Two powerfull CPUs are used.
Over 35,000 lines of software for performance that cannot be found in any other amplifier.
Fully Automatic
Easy connection with all models "ICOM, YAESU, KENWOOD, TEN-TEC, FlexRadio ELECRAFT" for immediate management of the bands, tuner and antennas.
Same performance with all makes or homemade rigs.
The operator has only to move the “Frequency Tuning Knob” in the transceiver!!!
Wide frequency coverage
1.8 MHz to 50 MHz including WARC bands.
Fully solid state
Up to 2 KW pep SSB, CW out; 50 MHz included.
MAX / MID (1KW) / LOW (500W) power selected according to the operator SSB/CW power requirement, for digital modes and for linear protection (automatic).
No heating time, immediately ready!
Virtually limitless life of the amplification devices ((6 MOSFETs MRF151G).
Automatic Antenna Tuner built-in
Capable of matching 3:1 SWR on HF, and 2.5:1 SWR on 6 meters.
Capable of programmable switching of 6 antennas (SO239 connectors).
Up to 3 antennas for the same band.
Management of the SteppIR / Ultrabeam antennas (tuneable).
Measure also the SWR of the antenna / cable system.
Bands, Antennas, Tuning conditions are changed in 10 msec.
Bands, Antennas and Tuning conditions are managed also in “STBY“ to support the exciter only.
Max. attenuation 0.8 dB.
Bypass capability.
Remotable (option).
SO2R
Two inputs available.
SO239 connectors.
High power gain (up to 14.5 dB).
In “OPERATE“ the required drive power is automatically set with an ALC connection and in “STANDBY“ the exciter is then automatically reset to full power.
Very clean and low distortion output!
Spurious emissions less than -60 dB ( 50 MHz –65 dB ).
3rd order distortion (two tone test) 36 dB typ.
Input 50 ohm always perfectly matched
SWR less than 1.2:1.
Fully protected
Temperature, Over-Voltage, Over-Current, SWR, Reflected Power, Max RF Tuner Voltage, Over-Drive, Amp. The correct parameters are continuously monitored.
The same protection is realized in two different ways:
· Via hardware circuits (HW) to assure great speed.
· Via the software (SW), to assure great accuracy.
Thanks to the SW, transmit relay changeover is carried out with zero current at the contacts.
Full break-in operation (QSK)
Quiet operation.
Linear management of the speed of the cooling fans of the heatsink.
In the power supply, fans speed is reduced during the reception.
Since, considering the big power developed, a significant amount of heat must be removed, every precaution is used to keep the lowest possible the noise of the fans.
Continuous use
“MAX” mode: SSB / CW unlimited.
Automatically switches to “MID” for a while if, in “MAX”, a continuous signal (RTTY) is transmitted.
“MID” “LOW” modes, RTTY unlimited.
Switching power supply.
Continous input between 190 – 255 Vac, 47-63 Hz.
PFC (Power Factor Correction).
The linear can be switched ON / OFF also switching ON / OFF the exciter.
Fully remotable.
With a large LCD display is possible to have a great deal of information
W pep out, V pa, I pa, W, Power gain, Temperatures, SWR (after and before the ATU), Input setting, CAT setting, Band and other indications including an alarms log.
Easy to operate
Powerful SW gives you a user-friendly unit.
USB port.
For remote control.
For new SW releases download.
Easy transportation
A sturdy carry-bag is supplied for “QSY, FIELD DAY, DX’ PEDITIONS etc.“.
Certifications :
CE, FCC.
The smallest in its class. Built-in Power supply and Automatic Antenna Tuner.
Dimension: L 38, H 18.3, P 43 cm (14.96” W, 7.20” H,16.93” D) (connettors included).
Weight: approx: 25 Kg.(55lbs).
The most technologically advanced in the world
Two powerfull CPUs are used.
Over 35,000 lines of software for performance that cannot be found in any other amplifier.
Fully Automatic
Easy connection with all models "ICOM, YAESU, KENWOOD, TEN-TEC, FlexRadio ELECRAFT" for immediate management of the bands, tuner and antennas.
Same performance with all makes or homemade rigs.
The operator has only to move the “Frequency Tuning Knob” in the transceiver!!!
Wide frequency coverage
1.8 MHz to 50 MHz including WARC bands.
Fully solid state
Up to 2 KW pep SSB, CW out; 50 MHz included.
MAX / MID (1KW) / LOW (500W) power selected according to the operator SSB/CW power requirement, for digital modes and for linear protection (automatic).
No heating time, immediately ready!
Virtually limitless life of the amplification devices ((6 MOSFETs MRF151G).
Automatic Antenna Tuner built-in
Capable of matching 3:1 SWR on HF, and 2.5:1 SWR on 6 meters.
Capable of programmable switching of 6 antennas (SO239 connectors).
Up to 3 antennas for the same band.
Management of the SteppIR / Ultrabeam antennas (tuneable).
Measure also the SWR of the antenna / cable system.
Bands, Antennas, Tuning conditions are changed in 10 msec.
Bands, Antennas and Tuning conditions are managed also in “STBY“ to support the exciter only.
Max. attenuation 0.8 dB.
Bypass capability.
Remotable (option).
SO2R
Two inputs available.
SO239 connectors.
High power gain (up to 14.5 dB).
In “OPERATE“ the required drive power is automatically set with an ALC connection and in “STANDBY“ the exciter is then automatically reset to full power.
Very clean and low distortion output!
Spurious emissions less than -60 dB ( 50 MHz –65 dB ).
3rd order distortion (two tone test) 36 dB typ.
Input 50 ohm always perfectly matched
SWR less than 1.2:1.
Fully protected
Temperature, Over-Voltage, Over-Current, SWR, Reflected Power, Max RF Tuner Voltage, Over-Drive, Amp. The correct parameters are continuously monitored.
The same protection is realized in two different ways:
· Via hardware circuits (HW) to assure great speed.
· Via the software (SW), to assure great accuracy.
Thanks to the SW, transmit relay changeover is carried out with zero current at the contacts.
Full break-in operation (QSK)
Quiet operation.
Linear management of the speed of the cooling fans of the heatsink.
In the power supply, fans speed is reduced during the reception.
Since, considering the big power developed, a significant amount of heat must be removed, every precaution is used to keep the lowest possible the noise of the fans.
Continuous use
“MAX” mode: SSB / CW unlimited.
Automatically switches to “MID” for a while if, in “MAX”, a continuous signal (RTTY) is transmitted.
“MID” “LOW” modes, RTTY unlimited.
Switching power supply.
Continous input between 190 – 255 Vac, 47-63 Hz.
PFC (Power Factor Correction).
The linear can be switched ON / OFF also switching ON / OFF the exciter.
Fully remotable.
With a large LCD display is possible to have a great deal of information
W pep out, V pa, I pa, W, Power gain, Temperatures, SWR (after and before the ATU), Input setting, CAT setting, Band and other indications including an alarms log.
Easy to operate
Powerful SW gives you a user-friendly unit.
USB port.
For remote control.
For new SW releases download.
Easy transportation
A sturdy carry-bag is supplied for “QSY, FIELD DAY, DX’ PEDITIONS etc.“.
Certifications :
CE, FCC.
Shipping:
We have several shipping options for our products, including next-day and Saturday/Sunday delivery for certain items. Please see these options at checkout.
Returns:
If you have any equipment that needs to be returned to Martin Lynch & Sons, please fill out the form below:
Upon receipt of goods you have 14 days to return goods however the goods must be returned in original packaging and care must have been taken with the goods you wish to return. Under distance selling regulations you are not entitled to any refund on carriage charges or modification charges made at your request. Large items cannot be returned if they have been assembled, unless faulty.
Warranty Terms and Conditions
Outside of the 14 faulty return period, returned items cannot be accepted, unless covered by manufacturer's warranty. We will repair as much as possible on site however in exceptional circumstances products may have to be returned to the manufacturer of distributor.
For repairs/replacements under manufacturer’s warranty for any item please download a ML&S return form from the link above and return to ML&S with the faulty product.
International Warranty information
Warranty service for items we sell is available in the U.K. only, unless otherwise noted. It is your responsibility to pay freight for returned items to the U.K. and back to you for desired warranty coverage. All of our NEW products come with a minimum 12 month warranty, (Yaesu & Icom 24 months), with up to 90 days on second-hand equipment. Items returned for service must state "returned goods for repair" on the return air waybill or U.K. import customs duties apply and will be added to your invoice. For more info about returning items please contact our customer help desk, [email protected]