Apache Labs ANAN-7000DLE 100W HF & 6M Transceiver

Apache Labs ANAN-7000DLE 100W HF & 6M Transceiver
RRP: £ 3099.95
£2949.95 ( £2458.29 EXC. VAT )
Add to cart
Product Information
  • Overview
  • ANAN-7000DLE Description

IN STOCK NOW!  WHY WAIT for "back-order"???

Interested in the PiHPSDR? Save £100 if you buy a 7000DLE with PiHPSDR! 


The ANAN-7000DLE – Second to none!

  • Using Direct Down Conversion with an ultra low phase noise clock yields an RMDR of 116dB @ 2Khz separation, this means that close in weak signals will not be masked by the receiver’s phase noise.
  • The transmitter specifications are also off the chart, use of a new 16bit DAC with an ultra low noise clock source results in transmit phase noise better than any other product available in the market.
  • Use of LDMOS drivers and an optimized final Amplifier stage with adaptive Predistortion Algorithm (PureSignal) yields transmit IMD of -68db @ 100W PEP, this is at least 20dB better than any Class A transmitter and over 30dB better than the competition.
  • Use of two 16bit phase synchronous ADCs allow for advanced applications such as Diversity reception for ultimate noise mitigation and effects of signal fading.
  • The ANAN-7000DLE HF & 6M 100W SDR Transceiver offers top of the line performance is a compact rugged package, it is based on the work of the OpenHPSDR community.

    The new PA board incorporates the following updates over the previous generation:
    1. PA Gain redistribution for better IMD
    2. Thermally compensated Bias
    3. Current/Voltage/Temp Sensors
    4. Temp controlled internal and option for external FAN
    5. Independent BPFs and 6M LNAs for each ADC, option to ground ADC2 on Tx
    6. Several other minor tweaks

General Specifications:

  • Architecture: Direct Sampling DDC/DUC Transceiver
  • Interface: Ethernet
  • Phase Noise (Clock): -149dB @ 10Khz
  • TCXO Stability (Typical): /- .1 PPM
  • Modes: CW, SSB, NFM, AM, Digital
  • Antenna Ports: Three BNC 50 ohms Software Configurable Ports, Three BNC ADC1 Bypass and Loop in ports, One BNC for RX2
  • Frequency Resolution: 1 Hz

 

Electrical Specifications:

  • 13.8v DC @ 25A, 3A Receive/25A Transmit

 

Mechanical Specifications:

  • 5Kg (approx. Weight)
  • Dimensions: 276MM (L) x 79MM (H) x 265MM (W) (Not including extrusions)
  • Rugged Aluminum Extrusion with Temperature controlled internal/External (Optional) Fan.

 

Receiver Specifications:

  • Receiver Architecture: Direct Down Conversion
  • Dual 16 bit Phase Synchronous ADCs
  • Independent filter banks for each ADC
  • 6M LNAs
  • Frequency Coverage: 9Khz to 60Mhz
  • Attenuator: 1-30dB step attenuator
  • Reciprocal Mixing Dynamic Range (RMDR): 116dB @ 2Khz offset
  • Receiver Phase noise: -149dB @ 10Khz
  • Image rejection: 90dB
  • Hardware support for 7 independent receivers assignable to either ADC

 

Transmitter Specifications:

  • Transmitter Architecture: Direct Up Conversion
  • DAC Resolution: 16 bit
  • RF Output Power: 100W SSB, CW, FM, RTTY, Digital; 1-30W AM
  • IMD: IMD3 typically -68dB below PEP @ 100W output on 20M
  • Harmonics: Typically better than -43dBc on HF and -60dBc on 6M
  • Carrier and Opposite Sideband Suppression: Better than -80dBc
  • Transverter IF Output: 0db to 15dB

 

IOs:

  • RCA Line In, Line Out, PTT in, PTT Out
  • DB9 Seven Software Configurable Open Collector Outputs
  • SMA XVTR, 10Mhz Reference Input
  • 3.25mm Barrel Mic, CW Key, Headphones and  two 6.25mm Speaker Outputs
  • RJ45 Ethernet LAN Connector
Recently Viewed
If you’d like us to let you know as soon as this product comes back into stock, please enter your email address and mobile number below.
Yaesu
Icom