Read More
Seen this product cheaper elsewhere?
Call 0345 2300 599
Icom IC-7760
Icom's innovative 200W HF and 50MHz transceiver with a full control head, separate RF deck, dual independent receivers and advanced RF direct-sampling architecture.
Call the team on 0345 2300 599 and we'll match or beat it.
Icom IC-7760 at ML&S
The Icom IC-7760 is a 200W HF/50MHz amateur radio transceiver introducing Icom's new Innovative Shack Style, with a full control head and separate RF deck connected by a control cable for far greater installation flexibility.
A 3 metre / 9.8ft control cable is supplied. A commercially available Cat5e or higher LAN cable can also be used for a direct connection of up to 100 metres, allowing the RF deck to be installed away from the operating desk and potentially closer to the antenna feed point.
The control head and RF deck can also communicate through a wired home LAN. This enables the controller to be operated from another suitable location in the home without requiring a PC at the RF deck.
MAIN and SUB dual touchscreen displays provide extensive operating information while keeping important controls immediately accessible. The 7-inch main display handles frequencies, operating status, spectrum information and metering, while the separate 2.4-inch touchscreen can display filter effects, meters and band stacking registers.
The receiver uses an advanced RF direct-sampling system with independent MAIN and SUB receivers. DIGI-SEL and the preamp can also be used together, allowing the preamp to improve sensitivity while the digital pre-selector helps reject strong unwanted out-of-band signals.
On transmit, the IC-7760 combines up to 200W output with Icom's Digital Pre-Distortion (DPD) technology for improved transmitted signal cleanliness. A built-in relay-type automatic antenna tuner, dual spectrum scopes and extensive contest and DX functions complete a transceiver designed for demanding HF operation.
Icom IC-7760 Highlights
- Full control head with separate RF deck for greater installation flexibility
- In-house remote operation through a wired LAN
- Independent MAIN and SUB receivers
- Advanced RF direct-sampling architecture with FPGA processing
- 7-inch main touchscreen and 2.4-inch sub touchscreen
- Dual spectrum scope and waterfall display
- DIGI-SEL and preamp can operate simultaneously
- 15 separated band-pass filters
- Up to 200W RF output
- Digital Pre-Distortion for cleaner transmitted signals
- 200W full-duty capability under Icom's specified operating conditions
- Built-in relay-type automatic antenna tuner
- Dual speakers for MAIN and SUB audio
- Preset FT8 menu
- RTTY and PSK encoder/decoder
- SD card slot
- I/Q signal output
- RS-BA1 remote operation support
- DVI-D external display output
LAN communication performance depends on the network environment. Gigabit Ethernet is required for in-house network operation.
Icom specifies 200W full-duty operation under stated operating conditions. Refer to the manufacturer's documentation for full details.
Want to See More?
Download the official IC-7760 brochure for additional information, specifications and connection details.
Download the IC-7760 BrochureIcom IC-7760
IC-7760 General
Flexible Station Installation
A 3m control cable is supplied. A Cat5e or higher LAN cable can be used for longer direct connections up to 100m, while the control head and RF deck can also communicate through a wired LAN network.
Dual Independent Direct-Sampling Receivers
Published typical figures with P.AMP1 enabled on HF and P.AMP2 enabled on 50MHz.
| Mode | Frequency | Sensitivity |
|---|---|---|
| SSB / CW | 135 / 475kHz | 1.41µV typical |
| SSB / CW | 1.8-30MHz | 0.16µV typical |
| SSB / CW | 50MHz | 0.13µV typical |
| AM | 0.5-1.8MHz | 6.3µV typical |
| AM | 1.8-30MHz | 2.0µV typical |
| AM | 50MHz | 1.0µV typical |
| FM | 28.0-29.7MHz | 0.5µV typical |
| FM | 50MHz | 0.32µV typical |
Spectrum, Waterfall, Filters & Metering
200W RF Output
The PA uses a 450W-class 65V LDMOS-FET together with a large heatsink and active cooling. Icom specifies one-hour continuous 200W transmission under its stated test conditions.
Built-In Relay-Type ATU
Operating & Station Functions
- Separate control head and RF deck
- Remote operation through LAN
- Dual identical independent receivers
- Dual speakers
- Dual spectrum scope and waterfall
- Audio scope with FFT and oscilloscope
- DSP processing in both the RF deck and control head
- DIGI-SEL digital preselector
- 15 separated band-pass filters
- IP+ function
- Main/Sub tracking for diversity reception
- Digital Pre-Distortion
- I/Q signal output
- RTTY and PSK encoder/decoder
- Preset FT8 menu
- Automatic contest serial numbering
- SD card slot
- DVI-D external display output
- VOX
- Transverter connection
- Microphone equaliser
- Adjustable transmit bandwidth
- 50 CTCSS tones
- Electronic keyer
- CW auto tuning
- Full and semi break-in CW
- APF Audio Peak Filter
- Quick Split and Quick Dualwatch
- Multi-function meter
- Separate external speaker outputs for MAIN and SUB
- USB support for the optional RC-28, keyboard, mouse and USB flash drive
- AH-730 external antenna tuner control
Shipping:
We have several shipping options for our products, including next-day and Saturday/Sunday delivery for certain items. Please see these options at checkout.
Returns:
If you have any equipment that needs to be returned to Martin Lynch & Sons, please fill out the form below:
Upon receipt of goods you have 14 days to return goods however the goods must be returned in original packaging and care must have been taken with the goods you wish to return. Under distance selling regulations you are not entitled to any refund on carriage charges or modification charges made at your request. Large items cannot be returned if they have been assembled, unless faulty.
Warranty Terms and Conditions
Outside of the 14 faulty return period, returned items cannot be accepted, unless covered by manufacturer's warranty. We will repair as much as possible on site however in exceptional circumstances products may have to be returned to the manufacturer of distributor.
For repairs/replacements under manufacturer’s warranty for any item please download a ML&S return form from the link above and return to ML&S with the faulty product.
International Warranty information
Warranty service for items we sell is available in the U.K. only, unless otherwise noted. It is your responsibility to pay freight for returned items to the U.K. and back to you for desired warranty coverage. All of our NEW products come with a minimum 12 month warranty, (Yaesu & Icom 24 months), with up to 90 days on second-hand equipment. Items returned for service must state "returned goods for repair" on the return air waybill or U.K. import customs duties apply and will be added to your invoice. For more info about returning items please contact our customer help desk, [email protected]