Read More

Seen this product cheaper elsewhere?
Call 0345 2300 599Aurora AU-510M
500W HF/6m SDR with Integrated 8-inch Touchscreen
High-power amateur radio, intelligently integrated. The FlexRadio Aurora AU-510M brings together a 500W HF transmitter, advanced direct-sampling SDR, automatic antenna tuner, AC power supply and Maestro-style front-panel controls in one compact, complete station.
500 Watts. No Separate Amplifier.
Aurora replaces the traditional collection of a transceiver, high-power amplifier, automatic antenna tuner and separate DC power supply with one integrated system, reducing station cabling, complexity and heat generation.
Integrated Transmitter
Up to 500W PEP across supported HF bands, with no external linear amplifier needed.
Automatic Antenna Tuner
Built-in high-power antenna matching for suitable antenna systems.
Internal Power Supply
Wide-range 80–264V AC input without an external high-current DC supply.
All the power. All the control. One radio.
The FlexRadio Aurora AU-510M combines the convenience of a conventional high-end transceiver with the flexibility of a modern software-defined radio. Its innovative polar-modulation transmitter provides substantial RF output without a separate amplifier, while the integrated Maestro-style front panel makes everyday operation intuitive.
Designed for HF and 50MHz operation, the AU-510M incorporates one high-performance Spectral Capture Unit supporting two independent slice receivers. Operators can monitor two separately configured frequencies and modes, with sophisticated panadapter displays and digital signal processing available through SmartSDR.
The built-in touchscreen offers standalone operation, while SmartSDR and SmartLink provide additional control through compatible computers and remote clients. From a permanent home station to a sophisticated transportable setup, Aurora makes powerful SDR operation remarkably straightforward.
HF PEP Output
Adjustable 1–500W PEP across supported 160m–10m amateur bands.
50MHz PEP Output
High-power 6m operation, subject to mode and duty-cycle requirements.
Slice Receivers
Two independently configurable receive frequencies and operating modes.
IPS Touchscreen
1920 × 1200 display with integrated physical tuning controls.
A fundamentally different approach to high-power RF
Aurora's transmitter uses polar modulation rather than a traditional linear power amplifier. By processing amplitude and phase information separately using specialised digital control and switching-mode amplification, the system achieves very high efficiency.
FlexRadio specifies approximately 80% transmitter efficiency under nominal conditions. This significantly reduces wasted power and heat compared with many conventional amplifier arrangements, helping make it possible to integrate 500W capability in a remarkably compact chassis.
Nominal Efficiency
More input power becomes useful RF instead of waste heat.
Specified Transmit Consumption
Manufacturer-published AC input figure under specified operating conditions.
Integrated Chassis
Transceiver, high-power transmitter, ATU and mains PSU together.
Efficiency and power consumption vary with operating mode, RF power and duty cycle.
Two receivers. One highly capable SDR platform.
The AU-510M uses one Spectral Capture Unit (SCU) with two independently configurable slice receivers. Each slice can be assigned its own frequency, operating mode and receive settings within the capabilities of the shared SCU.
This makes it convenient to monitor different frequencies, operate split and keep track of activity across the band. Both slices are supported by FlexRadio's direct-sampling receiver architecture and sophisticated DSP processing.
Two Slice Receivers
Independently tune and configure two receive slices.
Full-Duplex Operation
Supports compatible cross-band transmit and receive arrangements.
Receive-Only Input
Use a suitable dedicated receiving antenna through the RX-only port.
Transverter Port
Connect a compatible external transverter for supported applications.
Precision direct sampling and advanced DSP
At the heart of the AU-510M is a 16-bit direct-sampling receiver operating at 122.88 Msps. Its third-order amateur-band preselectors, DSP filtering and high dynamic range are designed for demanding HF and 6m operating conditions.
Direct Sampling
High-resolution analogue-to-digital conversion.
Msps Sampling Rate
High-speed SDR conversion and processing.
Published RMDR
Manufacturer specification at 2kHz spacing.
Order Preselectors
Amateur-band filtering ahead of the receive path.
The best of SDR, with the controls you know
The AU-510M includes an integrated Maestro-style operating panel, combining an 8-inch IPS touchscreen with dedicated physical tuning controls and buttons. This gives operators direct control of the radio without needing a separate computer.
Its 1920 × 1200 display provides high-resolution frequency, spectrum and waterfall information, with support for two panadapter views. An external HDMI connection provides additional display flexibility for compatible monitor installations.
8-inch IPS Touchscreen
Full-colour 1920 × 1200 high-resolution display.
Physical Controls
Dedicated tuning and operating controls built into the radio.
Two Panadapters
Spectrum and waterfall information on the built-in display.
External HDMI
Support for a compatible external display.
Operate at the radio or from somewhere else
The AU-510M's integrated front panel is only one way to operate. FlexRadio's SmartSDR ecosystem also supports computer-controlled operation and compatible remote clients, allowing operators to configure a station around the way they prefer to use it.
SmartLink provides supported remote access over the internet, while MultiFlex supports two compatible clients accessing the same radio. DAX audio and IQ channels provide useful connectivity for data-mode applications and other compatible software.
SmartLink
Supported internet-based remote station access.
MultiFlex
Two-client shared-radio operating capability.
DAX Audio / IQ
Two digital audio and two IQ data channels.
Client Flexibility
Compatible desktop, mobile and Maestro-style clients.
Some client applications and advanced functions may require separate licences or specific SmartSDR versions.
Integrated antenna matching and flexible connections
Aurora's built-in high-power automatic antenna tuner matches suitable antennas within its specified 3:1 SWR range. The AU-510M also provides two high-power main antenna connections, a dedicated receive-only input and a transverter/exciter port for suitable station configurations.
500W Automatic ATU
High-power antenna matching without a separate tuner.
Main Antenna Ports
High-power antenna connections for supported HF/6m operation.
RX-Only Port
Connect a suitable dedicated receiving antenna.
Transverter Connection
Configurable low-level drive for compatible transverters.
GNSS-referenced frequency stability
The AU-510M includes an integrated GNSS receiver supporting GPS, Galileo, GLONASS, QZSS and SBAS. With suitable satellite reception, it can provide highly accurate frequency control without regular manual oscillator adjustments.
The platform offers approximately 0.001ppm GNSS-referenced frequency stability and 0.5ppm internal TCXO stability. An optional high-performance GPSDO can provide an ultra-stable 10MHz reference output for compatible external equipment.
Standard GNSS functionality is included. The high-performance GPS-disciplined oscillator is an optional upgrade.
AU-510M vs AU-520M: Which is right for you?
Both models provide the same maximum transmitter power, integrated automatic tuner, AC power supply, 8-inch IPS touchscreen and Maestro-style physical controls. The main difference is their receiver architecture: the AU-510M features one SCU and two slice receivers, while the AU-520M adds a second SCU, four receivers and advanced multi-antenna contesting capabilities.
| Feature | AU-510M | AU-520M |
|---|---|---|
| HF / 6m PEP | 500W / 200W | 500W / 200W |
| Integrated Touchscreen | 8-inch | 8-inch |
| SCUs | 1 | 2 |
| Slice Receivers | 2 | 4 |
| ADC Sampling | 122.88 Msps | 245.76 Msps |
| Band Preselectors | 3rd order | 7th order |
| RX-Only Ports | 1 | 2 |
| Transverter Ports | 1 | 2 |
| True Diversity | No | Yes |
| Integrated SO2R | No | Yes |
| Internal ATU / PSU | Both included | Both included |
Choose the AU-510M if...
You want 500W HF output, a premium integrated touchscreen and two independent slice receivers without needing the more advanced multi-antenna and contesting capabilities of the dual-SCU model.
Choose the AU-520M if...
You need four slice receivers, two independent SCUs, true diversity, additional receive inputs and integrated SO2R in addition to the same 8-inch touchscreen.
View AU-520M at ML&S →Built for modern operating modes
The AU-510M supports SSB, CW, AM, SAM, FM, RTTY and compatible software-based digital modes. SmartSDR's DAX integration provides digital audio and IQ routing for supported applications, including popular amateur-radio data-mode software.
The Aurora platform also includes support for SmartSignal adaptive predistortion and Controlled Envelope SSB (CESSB), subject to the functionality provided by the installed firmware.
For FT8, RTTY and other high-duty-cycle modes, follow FlexRadio's current guidance for RF power, operating duty cycle and transmitter temperature. Maximum PEP rating does not imply unrestricted continuous-carrier operation.
Plug straight into the mains
The AU-510M includes its own wide-range AC power supply, accepting 80–264V AC at 47–63Hz. This removes the need for the external high-current DC supplies traditionally required by high-power amateur-radio equipment.
Manufacturer figures specify approximately 35W receive consumption and 675W transmit consumption under stated operating conditions.
The AU-510M does not support direct 13.8V DC power input. Portable use requires an appropriately rated AC power source or inverter.
High-power SDR made practical
Home Stations
High-power operation and built-in touchscreen without multiple separate boxes.
DX Operating
500W HF power, strong receiver performance and flexible split-frequency operation.
Transportable Stations
Fewer components to pack, wire and power in temporary station installations.
Remote Operating
SmartSDR and SmartLink support compatible remote station arrangements.
Important information before ordering
Integrated display: The AU-510M includes the 8-inch touchscreen and physical front-panel controls.
Transmit output: Up to 500W PEP on HF and 200W PEP on 6m. Use properly rated antennas, coax, RF switches and accessories.
Antenna tuning: The internal ATU is intended for suitable antennas within its specified matching range.
Power: Integrated AC mains input; direct 13.8V DC operation is not supported.
GPSDO: High-performance GPS-disciplined oscillator is optional; standard GNSS functionality is included.
Software: Individual features may depend on installed SmartSDR firmware and software licences.
Aurora User Guide
Consult the official Aurora user guide for detailed setup instructions, operating information and technical guidance.
View Aurora User Guide →FlexRadio Aurora AU-510M
500W HF/200W 6m single-SCU SDR transceiver with two slice receivers, integrated 8-inch touchscreen, polar-modulation transmitter, automatic antenna tuner and internal mains power supply.
General Specifications
| Model | Aurora AU-510M |
|---|---|
| Manufacturer | FlexRadio Systems |
| Architecture | Single-SCU direct-sampling SDR |
| Receive Coverage | 30kHz–54MHz |
| Transmit Bands | 160m–6m amateur bands, destination dependent |
| Operating Modes | SSB, CW, AM, SAM, FM, RTTY and supported digital modes |
| Integrated Front Panel | 8-inch Maestro-style touchscreen and controls |
| Integrated ATU | Yes, up to 3:1 SWR matching range |
| Integrated Power Supply | Yes, 80–264V AC |
| Dimensions (H × W × D) | 171 × 356 × 337mm |
| Approximate Weight | 8kg class, nominal manufacturer figure |
Receiver and SDR Architecture
| Spectral Capture Units | 1 |
|---|---|
| Maximum Slice Receivers | 2 |
| Maximum Panadapters | 2 |
| ADC Resolution | 16-bit |
| ADC Sampling Rate | 122.88 Msps |
| RMDR at 2kHz Spacing | Up to 115dB, manufacturer specification |
| Maximum Spectrum Dynamic Range | Greater than 145dB, zoomed display figure |
| Band Preselectors | 3rd-order |
| Full-Duplex Operation | Supported in compatible cross-band configurations |
| True Diversity | Not supported — single SCU |
| Integrated SO2R | Not supported — available on AU-520M |
| DAX Audio Channels | 2 |
| DAX IQ Channels | 2 |
Transmitter Specifications
| Transmitter Architecture | High-efficiency polar modulation |
|---|---|
| 160m–10m Output | 1–500W PEP |
| HF AM Carrier Power | Up to 125W |
| 6m Output | 1–200W PEP |
| 6m AM Carrier Power | Up to 50W |
| Transmitter Efficiency | Up to approximately 80%, manufacturer figure |
| Harmonic Suppression | At least 60dB below carrier, published figure |
| SmartSignal | Adaptive predistortion, firmware dependent |
| CESSB | Controlled Envelope SSB, firmware dependent |
Integrated Display and Control
| Display | 8-inch IPS touchscreen |
|---|---|
| Resolution | 1920 × 1200 pixels |
| Physical Front Panel | Integrated Maestro-style controls |
| Integrated Panadapters | Up to 2 |
| Panadapter Bandwidth | 5kHz–7MHz |
| Minimum Spectrum Resolution | 5.85Hz per pixel, specified display setting |
| External Display | HDMI |
| Standalone Front-Panel Operation | Yes |
Antenna and Station Interfaces
| Main TX Antenna Connections | 2, high-power antenna outputs |
|---|---|
| Dedicated RX-Only Inputs | 1 |
| Transverter/Exciter Ports | 1 |
| Transverter Drive | 0 to +10dBm, configurable |
| Internal ATU | 500W-class, up to 3:1 SWR matching range |
| Reference Input | 10MHz |
| Network Interface | Ethernet, SmartSDR / SmartLink |
| External Monitor | HDMI |
GNSS and Frequency Reference
| GNSS Receiver | Integrated, 12-channel |
|---|---|
| Supported Systems | GPS, Galileo, GLONASS, QZSS, SBAS |
| Cold Start TTFF | Less than 35 seconds, specified conditions |
| GNSS-Referenced Frequency Stability | Approximately 0.001ppm |
| TCXO Stability | Approximately 0.5ppm |
| High-Performance GPSDO | Optional, provides 10MHz reference output |
Power Requirements
| Input Voltage | 80–264V AC |
|---|---|
| Mains Frequency | 47–63Hz |
| Power Factor | Greater than 0.94, specified conditions |
| Receive Power Consumption | Approximately 35W |
| Transmit Power Consumption | Approximately 675W, specified conditions |
| Direct 13.8V DC Operation | Not supported |
SmartSDR and Remote Operation
| Operating Platform | SmartSDR |
|---|---|
| Remote Access | SmartLink |
| Two-Client Support | MultiFlex |
| Digital Audio Channels | 2 DAX / 2 DAX IQ |
| Computer Clients | Compatible Windows and Mac software |
| Mobile Clients | Compatible iPhone / iPad applications |
| Software Features | Subject to installed firmware, licence and release schedule |
AU-510M vs AU-520M — Screen-Equipped Models
Both include an 8-inch touchscreen, 500W HF transmitter, 200W 6m output, integrated automatic antenna tuner and AC power supply. The AU-520M adds a second SCU, additional receiver resources and advanced contesting functions.
| Feature | AU-510M | AU-520M |
|---|---|---|
| HF / 6m Power | 500W / 200W | 500W / 200W |
| Integrated Screen | 8-inch | 8-inch |
| SCUs | 1 | 2 |
| Slice Receivers | 2 | 4 |
| ADC Sampling Rate | 122.88 Msps | 245.76 Msps |
| Preselectors | 3rd-order | 7th-order |
| RX-Only Ports | 1 | 2 |
| Transverter Ports | 1 | 2 |
| True Diversity | No | Yes |
| Integrated SO2R | No | Yes |
| Built-in ATU / PSU | Yes / Yes | Yes / Yes |
Important Operating Notes
Display: The AU-510M includes an integrated 8-inch screen and physical controls.
Output power: 500W PEP HF, 200W PEP 6m. All RF accessories must be suitably rated.
Antenna tuner: Integrated with a specified 3:1 SWR matching range.
Power: Wide-range AC only; direct 13.8V DC is not supported.
GNSS/GPSDO: GNSS receiver standard; high-performance GPSDO optional.
SmartSDR: Some advertised functions depend on the installed firmware version and software licence.
Aurora User Guide
Refer to the official Aurora user guide for setup, SmartSDR operating instructions and detailed technical guidance.
View Aurora User Guide →Delivery Information
Shipping & Delivery
We offer a range of UK and international delivery services, including next working day delivery and selected weekend options for eligible orders. Available services, prices and estimated delivery times are shown at checkout.
All orders are despatched within 24 hours. UK domestic orders placed before 2pm are despatched the same day, provided no modification or labour service has been purchased.
Same-Day Despatch
UK domestic orders placed before 2pm are despatched the same day, excluding orders requiring modification or labour services.
Weekend Delivery
Orders requiring weekend delivery must be placed before 2pm on Friday. Orders placed on Saturday are not eligible for next-day or Sunday delivery, even if Sunday Delivery is selected at checkout.
Delivery Service Availability
Delivery options depend on the size, weight, contents and destination of your parcel. Express and weekend services are subject to availability and applicable cut-off times. Oversized or exceptionally heavy items may require a specialist delivery quotation.
Returns Information
Returns & Cancellations
To arrange a return, please contact our team at [email protected] or call 0345 2300 599.
Download Returns FormChanged Your Mind?
Under the Consumer Contracts Regulations 2013, most purchases made online or by telephone can be cancelled within 14 days of receipt.
Cancellation Period
14 Days
Notify us of your cancellation within 14 days of receiving your goods.
Once you have notified us, you have a further 14 days to return the goods.
Condition of Returned Goods
Please handle all goods with care. Returned items must be in a resaleable condition, complete with their original packaging and all supplied accessories.
You may inspect goods as you would in a shop. However, handling beyond what is necessary for inspection may result in a lawful deduction from your refund to reflect any diminished value.
Important Conditions
Returns Exceptions
The following conditions apply to modified equipment, custom-made cable assemblies, software and labour services.
Postage Options
Return Postage Charges
Customers are responsible for the direct cost of returning unwanted or incorrectly ordered goods. You may arrange your own suitable return postage or choose one of our optional prepaid return services.
Standard Parcels
Royal Mail Return Label
£5.95
Per parcel
Suitable for eligible standard-sized parcels, subject to Royal Mail restrictions. Free collection is available.
Larger Parcels
DPD Return Label
£7.95
Per parcel
Suitable for larger or heavier parcels, including shipments containing batteries.
Collection Service
DPD Collection
£25.00
Per parcel
Available upon request for eligible addresses, subject to service availability.
Return Postage Information
All prepaid return charges will be confirmed before booking and deducted from your refund.
The prices above apply to eligible UK mainland returns. Oversized items, specialist products and returns from other destinations may require a separate quotation. Estimated return costs will be disclosed before purchase.
Faulty or Incorrectly Supplied Goods
Return postage charges do not apply to faulty, damaged or incorrectly supplied goods returned under statutory rights. In these circumstances, ML&S will arrange a free return using either the Royal Mail or DPD return label service described above.
DPD collection is an additional chargeable service and is not provided free of charge under your statutory rights.
Refund Information
Refunds
How Refunds Are Processed
Refunds are processed without undue delay following receipt and inspection of the returned goods, and no later than 14 days after we receive your returned parcel.
Refunds are issued to the original payment method. Any prepaid return postage charges or lawful deductions for diminished value will be itemised and provided upon request.
Product Support
Warranty Terms & Conditions
ML&S provides warranty cover on new and used equipment, subject to the conditions outlined below.
New Equipment
Minimum 2-Year Warranty
All new products supplied by ML&S include a minimum two-year warranty against manufacturing defects. Batteries are excluded and are covered by separate warranty terms.
Some manufacturers offer extended warranty cover, including a three-year warranty on eligible Yaesu equipment. Any additional cover is subject to the manufacturer's terms and conditions.
Used Equipment
3-Month Warranty
All used products supplied by ML&S include a three-month parts and labour warranty against manufacturing defects. Batteries are excluded from warranty cover.
Warranty Repairs & Exclusions
Our workshop may assess and repair faulty equipment on site or, where necessary, refer it to the manufacturer or an authorised service centre.
Warranty exclusions may include batteries, normal wear and tear, accidental damage, misuse and unauthorised modifications, as specified in the applicable warranty terms.
All warranties are provided in addition to your statutory consumer rights against ML&S, which are not limited by the warranty period.
Overseas Customers
International Returns & Warranty
Unless otherwise stated, ML&S warranty servicing is carried out in the United Kingdom. International customers must contact us before returning goods to confirm the appropriate shipping and customs requirements.
International Return Conditions
International customers are responsible for return postage unless the goods are faulty and ML&S has been notified within a reasonable time.
ML&S accepts no responsibility for additional charges arising from incorrectly completed customs documentation. Any additional duties charged to ML&S as a result will be billed to the customer before the goods are returned.
We're Here to Help
Need Help With a Return?
Our team can assist with returns, postage arrangements, equipment modifications and warranty claims.
Email ML&SAlternatively, call us on 0345 2300 599.
Nothing in these terms excludes or limits your statutory consumer rights.









