Read More

Seen this product cheaper elsewhere?
Call 0345 2300 599Aurora AU-520
500W Dual-SCU HF/6m Software-Defined Transceiver
A complete high-power station in one compact chassis. The FlexRadio Aurora AU-520 integrates an advanced dual-SCU SDR, 500W HF transmitter, high-power automatic antenna tuner and AC power supply, with the flexibility of SmartSDR computer and remote operation.
No Screen. No Compromises in RF Performance.
The AU-520 is supplied without an integrated touchscreen or Maestro-style front panel. It is intended for use with compatible SmartSDR software on a computer, an external Maestro controller or supported remote clients. The same dual-SCU receiver and 500W RF capabilities are available without paying for an integrated display.
A high-performance station, without the stack of equipment
The FlexRadio Aurora AU-520 brings a new level of integration to HF and 50MHz amateur radio. Its innovative polar-modulation transmitter delivers up to 500W PEP on supported HF bands and 200W PEP on 6m, without requiring a separate linear amplifier.
The transceiver also incorporates an automatic antenna tuner and wide-range AC power supply, dramatically reducing the number of separate components and interconnecting cables required for a high-power station.
Unlike conventional compact SDRs with a single receiver architecture, the AU-520 includes two independent Spectral Capture Units. This provides four slice receivers, true diversity and the additional isolation and flexibility required for advanced multi-band operating and contesting.
HF PEP Power
Adjustable 1–500W PEP across supported 160m–10m amateur bands.
50MHz PEP Power
Up to 200W PEP on 6m, subject to operating mode and limits.
Independent SCUs
Two RF capture paths for separate antennas and advanced receiver techniques.
Slice Receivers
Four independent frequency and mode selections through SmartSDR.
500W power, with far less wasted energy
Aurora's polar-modulation architecture separates amplitude and phase information, allowing specialised high-efficiency switching amplification instead of relying on a conventional linear power amplifier.
FlexRadio quotes approximately 80% nominal transmitter efficiency. The result is significantly less wasted heat and electrical power for a given RF output compared with many traditional high-power systems.
Nominal Efficiency
Efficient energy conversion reduces transmitter heat losses.
Specified AC Input
Manufacturer's transmit consumption figure under specified conditions.
Integrated Station
Radio, high-power transmitter, automatic tuner and PSU together.
Efficiency and AC consumption vary with output power, mode and operating conditions.
Two independent RF paths. Four receivers.
The AU-520 uses two independent Spectral Capture Units to digitise signals from separate antenna sources. Each SCU supports flexible receive processing, with four slice receivers available across the system.
This architecture enables operators to monitor multiple frequencies across bands, receive through different antennas and configure advanced workflows without multiple separate transceivers.
Four Slice Receivers
Independently control receive frequency and operating mode.
True Diversity
Combine suitable independent receiving antenna signals under supported configurations.
Integrated SO2R
Advanced contest workflows in a single radio, including OTRSP support.
Full Duplex
Supports simultaneous transmitting and receiving arrangements within system limits.
Engineered for strong-signal environments
The AU-520 combines high-resolution 16-bit direct sampling with sophisticated digital processing and seventh-order amateur-band preselectors. The architecture delivers strong interference rejection for crowded bands, DX operation and complex contesting environments.
Msps Sampling
Published 16-bit direct-sampling ADC architecture.
RMDR
Specified reciprocal mixing dynamic range at 2kHz spacing.
Order Preselectors
Contest-grade RF filtering with published band-to-band rejection exceeding 50dB.
Your station, on the screen you choose
The screenless AU-520 is designed around FlexRadio's SmartSDR ecosystem. Use compatible computer software or a separate Maestro controller to view panadapters, waterfalls, receiver controls and transmit settings.
SmartLink enables supported remote operation over an internet connection, while MultiFlex offers two-client operation. DAX provides digital audio and IQ channels for compatible software and data-mode applications.
SmartSDR
Software-based radio control with multiple panadapters and slices.
SmartLink
Remote station access using compatible clients and suitable internet connectivity.
MultiFlex
Two supported SmartSDR clients on the same radio.
DAX Audio and IQ
Four audio and four IQ data channels for software integration.
The AU-520 has no integrated front-panel display or standalone touchscreen interface. A compatible computer, Maestro controller or supported client device is required to operate it.
Designed around complex station needs
Two high-power transmitting antenna connections, two receive-only inputs and two transverter ports provide the flexibility required by serious amateur-radio stations. Dual SCUs allow different receiver antennas to be used simultaneously.
Two TX Antenna Ports
Main antenna outputs supporting the radio's specified high-power operation.
Two RX-Only Ports
Dedicated connections for suitable receive-only antennas.
Two XVTR Ports
Configurable low-level drive for compatible transverters.
Automatic Tuner
Built-in matching for antennas within the specified 3:1 SWR range.
GNSS-referenced frequency stability
The AU-520 includes an integrated GNSS receiver supporting GPS, Galileo, GLONASS, QZSS and SBAS. With suitable satellite reception, the radio achieves highly accurate frequency control without regular manual oscillator adjustment.
FlexRadio quotes approximately 0.001ppm GNSS-referenced stability and 0.5ppm TCXO stability. An optional high-performance GPSDO adds a precision 10MHz output for suitable external station equipment.
Standard GNSS functionality is integrated. The enhanced GPS-disciplined oscillator is a separate upgrade.
AU-520 vs AU-510: Which is right for you?
Both the AU-510 and AU-520 are screenless Aurora radios offering the same 500W HF/200W 6m transmitter, built-in automatic tuner, AC power supply and SmartSDR operating environment. The AU-520 adds a second SCU and more advanced receiver resources.
| Feature | AU-510 | AU-520 |
|---|---|---|
| Maximum HF / 6m | 500W / 200W | 500W / 200W |
| Built-in Display | No | No |
| SCUs | 1 | 2 |
| Slice Receivers | 2 | 4 |
| ADC Sampling Rate | 122.88 Msps | 245.76 Msps |
| Preselectors | 3rd order | 7th order |
| RX-Only Ports | 1 | 2 |
| XVTR Ports | 1 | 2 |
| True Diversity | No | Yes |
| Integrated SO2R | No | Yes |
| ATU and PSU | Included | Included |
Choose the AU-520 if...
You want four receivers, independent antenna capture paths, true diversity, enhanced preselector filtering or integrated SO2R, without paying for a built-in screen.
Choose the AU-510 if...
You want the same integrated 500W power, built-in ATU and SmartSDR operation, but one SCU and two slice receivers meet your requirements.
View AU-510 at ML&S →Built-in AC power and modern digital capability
The integrated supply accepts 80–264V AC, eliminating the need for an external high-current DC power supply. The AU-520 is designed for SmartSDR integration with suitable computers and compatible digital-mode applications.
It supports SSB, CW, AM, SAM, FM, RTTY and compatible software-based digital modes. SmartSignal adaptive predistortion and Controlled Envelope SSB are included in the Aurora platform's advertised feature set, subject to supported firmware availability.
For FT8, RTTY and other high-duty-cycle modes, follow FlexRadio's latest recommendations for output power, transmission duration and temperature. High PEP capability is not the same as unrestricted continuous-carrier operation.
One integrated platform for the station you want
Home SDR Stations
Integrate 500W output, receiver capability, antenna tuner and mains supply in one chassis.
Remote Stations
A screenless SmartLink-capable platform suited to remote control.
Contesting
Dual SCUs, four slices, band filtering and SO2R operating arrangements.
DXpeditions
Reduce the number of heavy pieces of equipment required for a high-power station.
Important information before ordering
No built-in screen: A compatible SmartSDR control device or external Maestro controller is required.
Output power: Up to 500W PEP HF and 200W PEP 6m. Use appropriately rated antennas, coaxial cables, switches and accessories.
Power supply: Integrated 80–264V AC input. Direct 13.8V DC operation is not supported.
Automatic tuner: Matching is provided for suitable antennas within the stated 3:1 SWR range.
GPSDO: High-performance 10MHz output reference is optional; standard GNSS support is included.
Software: Some advertised capabilities are subject to installed SmartSDR firmware, applicable licences or subsequent updates.
Aurora User Guide
For operating instructions, SmartSDR configuration and technical guidance, consult the official Aurora user guide.
View Aurora User Guide →FlexRadio Aurora AU-520
Screenless 500W HF/200W 6m dual-SCU software-defined transceiver with four slice receivers, diversity reception, SO2R, integrated automatic antenna tuner and AC power supply.
General Specifications
| Model | Aurora AU-520 |
|---|---|
| Manufacturer | FlexRadio Systems |
| Architecture | Dual-SCU direct-sampling SDR |
| Receive Coverage | 30kHz–54MHz |
| Transmit Bands | 160m–6m amateur bands, subject to destination settings |
| Modes | SSB, CW, AM, SAM, FM, RTTY and compatible digital modes |
| Built-in Screen | No |
| Integrated Maestro Panel | No; optional external controller supported |
| External Operating Interface | Compatible SmartSDR computer, mobile or Maestro client |
| Integrated ATU | Yes, 3:1 SWR matching range |
| Integrated PSU | Yes, wide-range AC |
| Dimensions | 171 × 356 × 337mm (H × W × D) |
| Approximate Weight | 8kg class, manufacturer nominal figure |
Receiver Specifications
| Spectral Capture Units | 2 |
|---|---|
| Maximum Slice Receivers | 4 |
| Maximum Panadapters | 4, within supported SmartSDR clients |
| ADC Resolution | 16-bit |
| Sampling Rate | 245.76 Msps, published AU-520 specification |
| RMDR at 2kHz | Up to 115dB, manufacturer figure |
| Band Preselectors | 7th-order |
| Band-to-Band Filtering | Greater than 50dB rejection under specified conditions |
| True Diversity | Supported |
| Full-Duplex Operation | Supported within operating limits |
| Integrated SO2R | Supported, including OTRSP compatibility |
| DAX Audio Channels | 4 |
| DAX IQ Channels | 4 |
Transmitter Specifications
| Transmitter Technology | High-efficiency polar modulation |
|---|---|
| 160m–10m Output | 1–500W PEP |
| HF AM Carrier | Up to 125W |
| 6m Output | 1–200W PEP |
| 6m AM Carrier | Up to 50W |
| Nominal Efficiency | Approximately 80% |
| Harmonic Suppression | At least 60dB below carrier, stated specification |
| SmartSignal | Adaptive predistortion, firmware dependent |
| CESSB | Controlled Envelope SSB, firmware dependent |
Antenna and Radio Interfaces
| Main Antenna Connections | 2, supporting specified high-power operation |
|---|---|
| Receive-Only Ports | 2 |
| Transverter Ports | 2 |
| Transverter IF Range | 100kHz–54MHz |
| Transverter Drive | Adjustable to +10dBm |
| Internal ATU | High-power, rated for 3:1 SWR matching range |
| Reference Input | 10MHz |
| Networking | Ethernet / SmartSDR |
| Integrated HDMI Display Output | No; video display is provided by the external operating client |
Frequency Reference and GNSS
| Built-in GNSS | 12-channel receiver |
|---|---|
| GNSS Systems | GPS, Galileo, GLONASS, QZSS, SBAS |
| Cold Start TTFF | Less than 35 seconds under specified conditions |
| GNSS Frequency Stability | 0.001ppm |
| Internal TCXO | 0.5ppm |
| Optional GPSDO | High-performance oscillator with 10MHz output |
AC Power Requirements
| Input | 80–264V AC |
|---|---|
| Frequency | 47–63Hz |
| Power Factor | Greater than 0.94, specified conditions |
| Receive Consumption | Approximately 35W |
| Transmit Consumption | Approximately 675W, specified conditions |
| 13.8V DC Input | Not supported |
Software and Remote Operation
| Software Platform | SmartSDR |
|---|---|
| Integrated Display | Not fitted |
| Remote Operating | SmartLink |
| Multi-Client | MultiFlex |
| Computer Clients | Compatible Windows PC / Mac clients |
| Mobile Clients | Compatible iPhone / iPad applications |
| External Maestro | Supported, optional |
| DAX Audio / IQ | 4 / 4 channels |
| Feature Availability | Subject to installed SmartSDR firmware and applicable licences |
AU-510 vs AU-520 — Screenless Model Comparison
Both radios have no integrated display and feature identical maximum RF output, integrated tuner and AC mains supply. The AU-520 provides additional receiver capability, antenna inputs and contesting functions.
| Feature | AU-510 | AU-520 |
|---|---|---|
| Output HF / 6m | 500W / 200W | 500W / 200W |
| Screen | None | None |
| SCUs | 1 | 2 |
| Slice Receivers | 2 | 4 |
| ADC Sampling | 122.88 Msps | 245.76 Msps |
| Preselectors | 3rd order | 7th order |
| RX-Only Ports | 1 | 2 |
| Transverter Ports | 1 | 2 |
| True Diversity | No | Yes |
| Integrated SO2R | No | Yes |
| Internal ATU / AC PSU | Both included | Both included |
Important Operating Notes
External interface: No integrated touchscreen or display. Compatible SmartSDR control hardware or software is required.
Transmit output: 500W PEP HF, 200W PEP 6m. Connect accessories suitable for the relevant RF power and transmission duty cycle.
Automatic tuner: Included, with specified 3:1 SWR matching range.
AC input: Wide-range 80–264V AC; direct 13.8V DC operation is not supported.
GPSDO: Optional. Standard GNSS functionality is included.
Software: Some functions may depend on firmware versions, software licences and future updates.
Aurora User Guide
Refer to the official Aurora user guide for setup, SmartSDR operating instructions and installation guidance.
View Aurora User Guide →Delivery Information
Shipping & Delivery
We offer a range of UK and international delivery services, including next working day delivery and selected weekend options for eligible orders. Available services, prices and estimated delivery times are shown at checkout.
All orders are despatched within 24 hours. UK domestic orders placed before 2pm are despatched the same day, provided no modification or labour service has been purchased.
Same-Day Despatch
UK domestic orders placed before 2pm are despatched the same day, excluding orders requiring modification or labour services.
Weekend Delivery
Orders requiring weekend delivery must be placed before 2pm on Friday. Orders placed on Saturday are not eligible for next-day or Sunday delivery, even if Sunday Delivery is selected at checkout.
Delivery Service Availability
Delivery options depend on the size, weight, contents and destination of your parcel. Express and weekend services are subject to availability and applicable cut-off times. Oversized or exceptionally heavy items may require a specialist delivery quotation.
Returns Information
Returns & Cancellations
To arrange a return, please contact our team at [email protected] or call 0345 2300 599.
Download Returns FormChanged Your Mind?
Under the Consumer Contracts Regulations 2013, most purchases made online or by telephone can be cancelled within 14 days of receipt.
Cancellation Period
14 Days
Notify us of your cancellation within 14 days of receiving your goods.
Once you have notified us, you have a further 14 days to return the goods.
Condition of Returned Goods
Please handle all goods with care. Returned items must be in a resaleable condition, complete with their original packaging and all supplied accessories.
You may inspect goods as you would in a shop. However, handling beyond what is necessary for inspection may result in a lawful deduction from your refund to reflect any diminished value.
Important Conditions
Returns Exceptions
The following conditions apply to modified equipment, custom-made cable assemblies, software and labour services.
Postage Options
Return Postage Charges
Customers are responsible for the direct cost of returning unwanted or incorrectly ordered goods. You may arrange your own suitable return postage or choose one of our optional prepaid return services.
Standard Parcels
Royal Mail Return Label
£5.95
Per parcel
Suitable for eligible standard-sized parcels, subject to Royal Mail restrictions. Free collection is available.
Larger Parcels
DPD Return Label
£7.95
Per parcel
Suitable for larger or heavier parcels, including shipments containing batteries.
Collection Service
DPD Collection
£25.00
Per parcel
Available upon request for eligible addresses, subject to service availability.
Return Postage Information
All prepaid return charges will be confirmed before booking and deducted from your refund.
The prices above apply to eligible UK mainland returns. Oversized items, specialist products and returns from other destinations may require a separate quotation. Estimated return costs will be disclosed before purchase.
Faulty or Incorrectly Supplied Goods
Return postage charges do not apply to faulty, damaged or incorrectly supplied goods returned under statutory rights. In these circumstances, ML&S will arrange a free return using either the Royal Mail or DPD return label service described above.
DPD collection is an additional chargeable service and is not provided free of charge under your statutory rights.
Refund Information
Refunds
How Refunds Are Processed
Refunds are processed without undue delay following receipt and inspection of the returned goods, and no later than 14 days after we receive your returned parcel.
Refunds are issued to the original payment method. Any prepaid return postage charges or lawful deductions for diminished value will be itemised and provided upon request.
Product Support
Warranty Terms & Conditions
ML&S provides warranty cover on new and used equipment, subject to the conditions outlined below.
New Equipment
Minimum 2-Year Warranty
All new products supplied by ML&S include a minimum two-year warranty against manufacturing defects. Batteries are excluded and are covered by separate warranty terms.
Some manufacturers offer extended warranty cover, including a three-year warranty on eligible Yaesu equipment. Any additional cover is subject to the manufacturer's terms and conditions.
Used Equipment
3-Month Warranty
All used products supplied by ML&S include a three-month parts and labour warranty against manufacturing defects. Batteries are excluded from warranty cover.
Warranty Repairs & Exclusions
Our workshop may assess and repair faulty equipment on site or, where necessary, refer it to the manufacturer or an authorised service centre.
Warranty exclusions may include batteries, normal wear and tear, accidental damage, misuse and unauthorised modifications, as specified in the applicable warranty terms.
All warranties are provided in addition to your statutory consumer rights against ML&S, which are not limited by the warranty period.
Overseas Customers
International Returns & Warranty
Unless otherwise stated, ML&S warranty servicing is carried out in the United Kingdom. International customers must contact us before returning goods to confirm the appropriate shipping and customs requirements.
International Return Conditions
International customers are responsible for return postage unless the goods are faulty and ML&S has been notified within a reasonable time.
ML&S accepts no responsibility for additional charges arising from incorrectly completed customs documentation. Any additional duties charged to ML&S as a result will be billed to the customer before the goods are returned.
We're Here to Help
Need Help With a Return?
Our team can assist with returns, postage arrangements, equipment modifications and warranty claims.
Email ML&SAlternatively, call us on 0345 2300 599.
Nothing in these terms excludes or limits your statutory consumer rights.









